DIY MAIN MENU

Hey!  Please help us by sharing this guide if you liked it!

Japan Aquaponics offers a growing amount of informational guides for anyone who is interested in aquaponics.  Please feel free to read this, and our other guides, and we welcome any questions that you may have.

 

Japan Aquaponics is a social enterprise set up to develop aquaponics, and particularly to promote its use in Tohoku - one of the areas worst affected by the earthquake and tsunami in northern Japan in March of 2011.

 

All information and our guides are offered freely - but please consider a donation if you are able.  All donations, and all profits of Japan Aquaponics, are used in projects in Tohoku.

DIY Aquaponics Guides

Bell Siphons & Loop Siphons

Micro Aquaponics Plans

Indoor Aquaponics System Plans

Step 3 - Making the water In-flow pipe

 

Take your 13mm male and female connectors and the two rubber washers, or O-rings.

 

Place the first O-ring on the male adapter and thread it through the top of the growbed. Then fit the 2nd rubber O-ring onto the threads and screw the female adapter onto the male adapter until you have a nice snug (and waterproof) fit.

 

Into the male adapter we then add a short length of 13mm pipe and add two 90 degree elbows on top of this.  (The elbows are connected by a short pice of 13mm pipe (36mm))

 

The height of this assembly just needs to be sufficient to clear the surface of the growbed when all the media is added.

 

 

 

 

Step 4 - Making the Ball-valve Bypass and Pump Connector

 

Here you can see the whole of the plumbing assembly that comes off the pump and draws water into the growbed.

 

We start at the bottom with the flexi-pipe that is connected to the pump - if your flexi-pipe does not fit onto the pump then use a small length of hosepipe that can fit into the flexi, and onto the pump.

 

We the use a T-bar that will draw some water up the straight length of 13mm pipe into the 13mm female connector and then on up to the growbed, and some water into the Ball-valve assembly to divert back into the fish tank.

 

From the T-bar add a small 13mm piece of pipe that fits into the Ball-valve.  Out of the Ball-valve we have another piece of pipe that goes into the corner of the fish tank, and ends in a 90 degree elbow to allow the water to flow smoothly into the tank.

 

None of the fittings are glued - all just pushed on firmly.  This allows us to take the assembly apart for cleaning if we need to.

 

This whole assembly allows us to control how much water flows into the growbed and so is an important addition. The ball-valve bypass also allows us to divert some water back to the fish tank and this provides additional aeration and water movement into the tank. This improves the health of the fish.

 

The ball-valve bypass and other aquaponics plumbing principles and practicalities can be seen in our Aquaponics Plumbing Guide.

Step 5

 

The bell siphon is a very effective method of slowly flooding the growbed and then draining the growbed quickly. It does this with a non-mechanical action, and with no moving parts to break.

 

We start with the 16mm male and female adapters that are connected to the growbed.  We use a slightly wider width than the inflowing plumbing to reduce any chance of flooding.

 

We use a small length of 16mm pipe to regulate the height of the water in the growbed.  However high the pipe is, will be how how the water reaches in the growbed.  We usually leave the top few cms of growbed completely dry.  You can use a reducer as shown here if you prefer - but it is not strictly necessary on these systems and works without it.

 

We then have the 50mm bell siphon in the middle. This is a 50 mm piece of pipe with an airtight cap on the top. This bell siphon has some pieces cut out of the bottom as well as some holes drilled in the side. You want these holes to be no higher than about 1 inch from the bottom of the pipe. The water will drain down to this level and will stop

 

The 100mm media guard on the far right is simply to keep the growbed media out of the bell siphon. This has holes drilled or cut out of it to allow the water to come in - and to keep the roots and the media out! The cap is optional, but helps to keep things out of the bell siphon.

 

Finally you can see the length of 16mm pipe under the growbed that returns the water back to the fish tank.

 

Bell siphons can be tricky to get working so for more information please refer to our Bell Siphon Guide.

Step 7

 

You should have all the framework, the containers, and the plumbing set up now. Now add water into the fish tank and start the pump up. We want to test to see if everything works properly, and if the system is watertight!

 

The next thing to do is to fill the top container (the growbed) with some sort of growing media. This could be hydroton, lava rock, perlite, river stones or something similar. Select media that allows the water to flow through the growbed.

 

Once this has been done, then you are ready to add your fish and to start putting plants into your system! Initially you should add only a couple of small fish just to start producing the ammonia needed to kick-start your system. Goldfish work really well.

 

Further information: Setting up your system is just the beginning and so we recommend checking out more information on how to actually run your system and how aquaponics works.

Back to Page 1

Would you consider a donation for charity?

Japan Aquaponics offers a huge amount of information and guides completely free of charge and all profit we make is donated to supporting disaster recovery efforts and community rebuilding in Tohoku.

 

Please consider making a small donation if you find this guide or any of our other guides helpful... just a couple of dollars could make a huge difference.  Thank you.

 

More Info - Aquaponics for Tohoku Projects

More Info - Latest Tohoku Project


Hey!  Please help us by sharing this guide if you liked it!

New to Aquaponics?

Click here for lots of info to get you started!